The GLUON_ATH10K_MESH must be set to 11s or ibss; when it is not set,
ath10k device images won't be built at all. This also allows us to remove
the BROKEN flag for ath10k devices, as the GLUON_ATH10K_MESH variable is
sufficient to avoid ath10k devices if desired.

Fixes #864

The MR1750 and OM5P-AC devices are based on ath9k SoCs and an external
ath10k chip. All devices which are using ath10k should be marked as broken
due to deficits in their IBSS support.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Fixes #842

[Matthias Schiffer: changed the text a bit]

+ added profile for these devices
+ added entry in the docs for these devices plus the missing alfa tube

Generate flashable images for the Archer C7 v2 with current stock firmware
again.

To set the region code, the GLUON_REGION variable must be set to "us" or
"eu" in site.mk or as a make argument.

Fixes #860

Allows weird release numbers, models and site names, and prepares support
for pretty hostnames.

and add documentation

Use the common term; the "Expert Mode" never was a distinct mode of
operation anyways.

Fixes #823

The new MR1750v2 device support is only available in LEDE master. The
relevant patches have to backported to add support for them in Gluon

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

The new OM2P-HSv3 device support is only available in LEDE master. The
relevant patches have to backported to add support for them in Gluon

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

The new ath9k/ath10k based devices are only available in OpenWrt trunk. The
relevant patches have to backported to add support for them in Gluon

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

This patch adds a new gluon-ebtables package to filter IGMP/MLD messages
via ebtables.

For one thing this reduces multicast overhead: About one third of all
ICMPv6 multicast traffic in Lübeck or Hamburg is MLD.

Furthermore it removes a potential Distributed Denial-of-Service vector
(see Gluon ticket #553).

Finally, it is a prerequisite for enabling bridge multicast snooping in
a decentral and robust fashion.

Note that IGMP/MLD are filtered for multicast traffic coming from
the mesh, too (new MULTICAST_IN), as unfortunately there seem to
be other queriers somewhere in the mesh at least for Freifunk
Lübeck. Also adding these rules to be prepared to anyone intentionally
or unintentionally disabling these filters on his/her node.

Node operators not running Gluon (for instance gateway nodes) should
make sure to either enable multicast_router towards bat0 or disable
multicast snooping entirely if they have a bridge on top of bat0.

Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>

Integrate OpenMesh devices available in OpenWrt Chaos Calmer:

 - MR600
 - MR600v2
 - MR900
 - MR900v2
 - OM2P
 - OM2P-HS
 - OM2P-HSv2
 - OM2P-LC
 - OM2Pv2
 - OM5P
 - OM5P-AN

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Device information can be found at:
http://www.8devices.com/products/carambola-2
https://wiki.openwrt.org/toh/8devices/carambola2

I only did some minimal testing of gluon on the carambola 2 development
board:

 - Config mode works
 - Connects to Wifi Mesh
 - Allows clients to connect

Notably, autoupgrade has not yet been tested.

Change to 010-primary-mac is necessary as the mac address printed
on the sticker is the one of eth0, not the wifi mac.

Newer versions of Sphinx would break lines at the colons.